User Contributed                                            MET/CAL Procedure
=============================================================================
INSTRUMENT:            OSP-4L Displacemet Sub
DATE:                  17-Sep-97
AUTHOR:		     User Contributed                                               
REVISION:
ADJUSTMENT THRESHOLD:  70%
NUMBER OF TESTS:       29
NUMBER OF LINES:       339
CONFIGURATION:         HP 34401A
=============================================================================
 STEP    FSC    RANGE NOMINAL        TOLERANCE     MOD1        MOD2  3  4 CON
  1.001  ASK-                        P                            F
  1.002  ASK+                                          X
  1.003  HEAD         {* Displacement Calibration *}
  1.004  HEAD         {  Channel 1 }
  1.005  JMP          2.001
  1.006  EVAL
  2.001  IEEE         [@34401]FUNC "VOLT:AC"[GTL]
  2.002  DISP         Set the UUT as follows:
  2.002  DISP         ACC/DISP ........................... DISP ALL
  2.002  DISP         SERVO .............................. ON
  2.003  DISP         Adjust the CROSSOVER controls for channel 1
  2.003  DISP         to be active.  Adjust the channel 1 vernier for 10.00.
  2.004  IEEE         [@34401]READ?[I][GTL]
  2.005  ACC    1     .3610V         0.06% 0.04/
  2.006  MEME
  2.007  MEMC         V              2.00%         .1inp-p
#!          Test Tol 0.00722, Sys Tol 0.0006166, TUR 11.709 (>= 4.00).
  3.001  IEEE         [@34401]FUNC "VOLT:AC"[GTL]
  3.002  IEEE         [@34401]SENS:DET:BAND 3
  3.003  DISP         Change the UUT frequency output to 5 Hz.
  3.003  DISP
  3.003  DISP         It may be necessary to adjust the CROSSOVER
  3.003  DISP         to keep channel 1 active.
  3.004  DISP         Set the UUT as follows:
  3.004  DISP         LEVEL MULTIPLIERS................... Both In
  3.004  DISP         SERVO .............................. ON
  3.005  IEEE         [@34401]READ?[I][GTL]
  3.006  ACC    0.1   .0903V         0.35% 0.04/
  3.007  MEME
  3.008  MEMC         V              3.0%          10inp-p
#!          Test Tol 0.002709, Sys Tol 0.00035605, TUR 7.608 (>= 4.00).
  4.001  IEEE         [@34401]FUNC "VOLT:AC"[GTL]
  4.002  DISP         Change the UUT frequency output to 10 Hz.
  4.002  DISP
  4.002  DISP         It may be necessary to adjust the CROSSOVER
  4.002  DISP         to keep channel 1 active.
  4.003  DISP         Set the UUT as follows:
  4.003  DISP         LEVEL MULTIPLIERS................... Both In
  4.003  DISP         SERVO .............................. ON
  4.004  IEEE         [@34401]READ?[I][GTL]
  4.005  ACC    1     .3610V         0.35% 0.03/
  4.006  MEME
  4.007  MEMC         V              3.0%          10inp-p
#!          Test Tol 0.01083, Sys Tol 0.0015635, TUR 6.927 (>= 4.00).
  5.001  IEEE         [@34401]FUNC "VOLT:AC"[GTL]
  5.002  IEEE         [@34401]SENS:DET:BAND 20
  5.003  DISP         Change the UUT frequency output to 20 Hz.
  5.003  DISP
  5.003  DISP         It may be necessary to adjust the CROSSOVER
  5.003  DISP         to keep channel 1 active.
  5.004  DISP         Set the UUT as follows:
  5.004  DISP         LEVEL MULTIPLIERS................... X100 (1in p-p)
  5.004  DISP         SERVO .............................. ON
  5.005  IEEE         [@34401]READ?[I][GTL]
  5.006  ACC    1     .1440V         0.06% 0.03/
  5.007  MEME
  5.008  MEMC         V              3.0%          1inp-p
#!          Test Tol 0.00432, Sys Tol 0.0003864, TUR 11.180 (>= 4.00).
  6.001  IEEE         [@34401]FUNC "VOLT:AC"[GTL]
  6.002  DISP         Change the UUT frequency output to 50 Hz.
  6.002  DISP
  6.002  DISP         It may be necessary to adjust the CROSSOVER
  6.002  DISP         to keep channel 1 active.
  6.003  DISP         Set the UUT as follows:
  6.003  DISP         LEVEL MULTIPLIERS................... X10 (.1in p-p)
  6.003  DISP         SERVO .............................. ON
  6.004  IEEE         [@34401]READ?[I][GTL]
  6.005  ACC    0.1   .0903V         0.06% 0.04/
  6.006  MEME
  6.007  MEMC         V              3.0%          1inp-p
#!          Test Tol 0.002709, Sys Tol 9.418e-005, TUR 28.764 (>= 4.00).
  7.001  IEEE         [@34401]FUNC "VOLT:AC"[GTL]
  7.002  DISP         Change the UUT frequency output to 500 Hz.
  7.002  DISP
  7.002  DISP         It may be necessary to adjust the CROSSOVER
  7.002  DISP         to keep channel 1 active.
  7.003  DISP         Set the UUT as follows:
  7.003  DISP         LEVEL MULTIPLIERS................... Both Out (.01in)
  7.003  DISP         SERVO .............................. ON
  7.004  IEEE         [@34401]READ?[I][GTL]
  7.005  ACC    1     .9030V         0.06% 0.03/
  7.006  MEME
  7.007  MEMC         V              3.0%          .01inp-p
#!          Test Tol 0.02709, Sys Tol 0.0008418, TUR 32.181 (>= 4.00).
  8.001  HEAD         { Channel 2 }
  8.002  JMP          9.001
  8.003  EVAL
  9.001  IEEE         [@34401]FUNC "VOLT:AC"[GTL]
  9.002  DISP         Adjust the oscillator controlls for a 100Hz output.
  9.003  DISP         Adjust the CROSSOVER controls for channel 2
  9.003  DISP         to be active.  Adjust the channel 2 vernier for 10.00.
  9.004  IEEE         [@34401]READ?[I][GTL]
  9.005  ACC    1     .3610V         0.06% 0.03/
  9.006  MEME
  9.007  MEMC         V              2.00%         .1inp-p
#!          Test Tol 0.00722, Sys Tol 0.0005166, TUR 13.976 (>= 4.00).
 10.001  IEEE         [@34401]FUNC "VOLT:AC"[GTL]
 10.002  IEEE         [@34401]SENS:DET:BAND 3
 10.003  DISP         Change the UUT frequency output to 5 Hz.
 10.003  DISP
 10.003  DISP         It may be necessary to adjust the CROSSOVER
 10.003  DISP         to keep channel 2 active.
 10.004  DISP         Set the UUT as follows:
 10.004  DISP         LEVEL MULTIPLIERS................... Both In
 10.004  DISP         SERVO .............................. ON
 10.005  IEEE         [@34401]READ?[I][GTL]
 10.006  ACC    0.1   .0903V         0.35% 0.04/
 10.007  MEME
 10.008  MEMC         V              3.0%          10inp-p
#!          Test Tol 0.002709, Sys Tol 0.00035605, TUR 7.608 (>= 4.00).
 11.001  IEEE         [@34401]FUNC "VOLT:AC"[GTL]
 11.002  DISP         Change the UUT frequency output to 10 Hz.
 11.002  DISP
 11.002  DISP         It may be necessary to adjust the CROSSOVER
 11.002  DISP         to keep channel 2 active.
 11.003  DISP         Set the UUT as follows:
 11.003  DISP         LEVEL MULTIPLIERS................... Both In
 11.003  DISP         SERVO .............................. ON
 11.004  IEEE         [@34401]READ?[I][GTL]
 11.005  ACC    1     .3610V         0.06% 0.03/
 11.006  MEME
 11.007  MEMC         V              3.0%          10inp-p
#!          Test Tol 0.01083, Sys Tol 0.0005166, TUR 20.964 (>= 4.00).
 12.001  IEEE         [@34401]FUNC "VOLT:AC"[GTL]
 12.002  IEEE         [@34401]SENS:DET:BAND 20
 12.003  DISP         Change the UUT frequency output to 20 Hz.
 12.003  DISP
 12.003  DISP         It may be necessary to adjust the CROSSOVER
 12.003  DISP         to keep channel 2 active.
 12.004  DISP         Set the UUT as follows:
 12.004  DISP         LEVEL MULTIPLIERS................... X100 (1in p-p)
 12.004  DISP         SERVO .............................. ON
 12.005  IEEE         [@34401]READ?[I][GTL]
 12.006  ACC    1     .1440V         0.06% 0.03/
 12.007  MEME
 12.008  MEMC         V              3.0%          1inp-p
#!          Test Tol 0.00432, Sys Tol 0.0003864, TUR 11.180 (>= 4.00).
 13.001  IEEE         [@34401]FUNC "VOLT:AC"[GTL]
 13.002  DISP         Change the UUT frequency output to 50 Hz.
 13.002  DISP
 13.002  DISP         It may be necessary to adjust the CROSSOVER
 13.002  DISP         to keep channel 2 active.
 13.003  DISP         Set the UUT as follows:
 13.003  DISP         LEVEL MULTIPLIERS................... X10 (.1in p-p)
 13.003  DISP         SERVO .............................. ON
 13.004  IEEE         [@34401]READ?[I][GTL]
 13.005  ACC    0.1   .0903V         0.06% 0.04/
 13.006  MEME
 13.007  MEMC         V              3.0%          1inp-p
#!          Test Tol 0.002709, Sys Tol 9.418e-005, TUR 28.764 (>= 4.00).
 14.001  IEEE         [@34401]FUNC "VOLT:AC"[GTL]
 14.002  DISP         Change the UUT frequency output to 500 Hz.
 14.002  DISP
 14.002  DISP         It may be necessary to adjust the CROSSOVER
 14.002  DISP         to keep channel 2 active.
 14.003  DISP         Set the UUT as follows:
 14.003  DISP         LEVEL MULTIPLIERS................... Both Out (.01in)
 14.003  DISP         SERVO .............................. ON
 14.004  IEEE         [@34401]READ?[I][GTL]
 14.005  ACC    1     .9030V         0.06% 0.03/
 14.006  MEME
 14.007  MEMC         V              3.0%          .01inp-p
#!          Test Tol 0.02709, Sys Tol 0.0008418, TUR 32.181 (>= 4.00).
 15.001  HEAD         { Channel 3 }
 15.002  JMP          16.001
 15.003  EVAL
 16.001  IEEE         [@34401]FUNC "VOLT:AC"[GTL]
 16.002  DISP         Adjust the oscillator controlls for a 100Hz output.
 16.003  DISP         Adjust the CROSSOVER controls for channel 3
 16.003  DISP         to be active.  Adjust the channel 3 vernier for 10.00.
 16.004  IEEE         [@34401]READ?[I][GTL]
 16.005  ACC    1     .3610V         0.06% 0.03/
 16.006  MEME
 16.007  MEMC         V              2.00%         .1inp-p
#!          Test Tol 0.00722, Sys Tol 0.0005166, TUR 13.976 (>= 4.00).
 17.001  IEEE         [@34401]FUNC "VOLT:AC"[GTL]
 17.002  IEEE         [@34401]SENS:DET:BAND 3
 17.003  DISP         Change the UUT frequency output to 5 Hz.
 17.003  DISP
 17.003  DISP         It may be necessary to adjust the CROSSOVER
 17.003  DISP         to keep channel 3 active.
 17.004  DISP         Set the UUT as follows:
 17.004  DISP         LEVEL MULTIPLIERS................... Both In
 17.004  DISP         SERVO .............................. ON
 17.005  IEEE         [@34401]READ?[I][GTL]
 17.006  ACC    0.1   .0903V         0.35% 0.04/
 17.007  MEME
 17.008  MEMC         V              3.0%          10inp-p
#!          Test Tol 0.002709, Sys Tol 0.00035605, TUR 7.608 (>= 4.00).
 18.001  IEEE         [@34401]FUNC "VOLT:AC"[GTL]
 18.002  DISP         Change the UUT frequency output to 10 Hz.
 18.002  DISP
 18.002  DISP         It may be necessary to adjust the CROSSOVER
 18.002  DISP         to keep channel 3 active.
 18.003  DISP         Set the UUT as follows:
 18.003  DISP         LEVEL MULTIPLIERS................... Both In
 18.003  DISP         SERVO .............................. ON
 18.004  IEEE         [@34401]READ?[I][GTL]
 18.005  ACC    1     .3610V         0.06% 0.03/
 18.006  MEME
 18.007  MEMC         V              3.0%          10inp-p
#!          Test Tol 0.01083, Sys Tol 0.0005166, TUR 20.964 (>= 4.00).
 19.001  IEEE         [@34401]FUNC "VOLT:AC"[GTL]
 19.002  IEEE         [@34401]SENS:DET:BAND 20
 19.003  DISP         Change the UUT frequency output to 20 Hz.
 19.003  DISP
 19.003  DISP         It may be necessary to adjust the CROSSOVER
 19.003  DISP         to keep channel 3 active.
 19.004  DISP         Set the UUT as follows:
 19.004  DISP         LEVEL MULTIPLIERS................... X100 (1in p-p)
 19.004  DISP         SERVO .............................. ON
 19.005  IEEE         [@34401]READ?[I][GTL]
 19.006  ACC    1     .1440V         0.06% 0.03/
 19.007  MEME
 19.008  MEMC         V              3.0%          1inp-p
#!          Test Tol 0.00432, Sys Tol 0.0003864, TUR 11.180 (>= 4.00).
 20.001  IEEE         [@34401]FUNC "VOLT:AC"[GTL]
 20.002  DISP         Change the UUT frequency output to 50 Hz.
 20.002  DISP
 20.002  DISP         It may be necessary to adjust the CROSSOVER
 20.002  DISP         to keep channel 3 active.
 20.003  DISP         Set the UUT as follows:
 20.003  DISP         LEVEL MULTIPLIERS................... X10 (.1in p-p)
 20.003  DISP         SERVO .............................. ON
 20.004  IEEE         [@34401]READ?[I][GTL]
 20.005  ACC    0.1   .0903V         0.06% 0.04/
 20.006  MEME
 20.007  MEMC         V              3.0%          1inp-p
#!          Test Tol 0.002709, Sys Tol 9.418e-005, TUR 28.764 (>= 4.00).
 21.001  IEEE         [@34401]FUNC "VOLT:AC"[GTL]
 21.002  DISP         Change the UUT frequency output to 500 Hz.
 21.002  DISP
 21.002  DISP         It may be necessary to adjust the CROSSOVER
 21.002  DISP         to keep channel 3 active.
 21.003  DISP         Set the UUT as follows:
 21.003  DISP         LEVEL MULTIPLIERS................... Both Out (.01in)
 21.003  DISP         SERVO .............................. ON
 21.004  IEEE         [@34401]READ?[I][GTL]
 21.005  ACC    1     .9030V         0.06% 0.03/
 21.006  MEME
 21.007  MEMC         V              3.0%          .01inp-p
#!          Test Tol 0.02709, Sys Tol 0.0008418, TUR 32.181 (>= 4.00).
 22.001  HEAD         { Channel 4 }
 22.002  JMP          23.001
 22.003  EVAL
 23.001  IEEE         [@34401]FUNC "VOLT:AC"[GTL]
 23.002  DISP         Adjust the oscillator controlls for a 100Hz output.
 23.003  DISP         Adjust the CROSSOVER controls for channel 4
 23.003  DISP         to be active.  Adjust the channel 4 vernier for 10.00.
 23.004  IEEE         [@34401]READ?[I][GTL]
 23.005  ACC    1     .3610V         0.06% 0.03/
 23.006  MEME
 23.007  MEMC         V              2.00%         .1inp-p
#!          Test Tol 0.00722, Sys Tol 0.0005166, TUR 13.976 (>= 4.00).
 24.001  IEEE         [@34401]FUNC "VOLT:AC"[GTL]
 24.001  IEEE         [@34401]SENS:DET:BAND 3
 24.002  DISP         Change the UUT frequency output to 5 Hz.
 24.002  DISP
 24.002  DISP         It may be necessary to adjust the CROSSOVER
 24.002  DISP         to keep channel 4 active.
 24.003  DISP         Set the UUT as follows:
 24.003  DISP         LEVEL MULTIPLIERS................... Both In
 24.003  DISP         SERVO .............................. ON
 24.004  IEEE         [@34401]READ?[I][GTL]
 24.005  ACC    0.1   .0903V         0.35% 0.04/
 24.006  MEME
 24.007  MEMC         V              3.0%          10inp-p
#!          Test Tol 0.002709, Sys Tol 0.00035605, TUR 7.608 (>= 4.00).
 25.001  IEEE         [@34401]FUNC "VOLT:AC"[GTL]
 25.002  DISP         Change the UUT frequency output to 10 Hz.
 25.002  DISP
 25.002  DISP         It may be necessary to adjust the CROSSOVER
 25.002  DISP         to keep channel 4 active.
 25.003  DISP         Set the UUT as follows:
 25.003  DISP         LEVEL MULTIPLIERS................... Both In
 25.003  DISP         SERVO .............................. ON
 25.004  IEEE         [@34401]READ?[I][GTL]
 25.005  ACC    1     .3610V         0.06% 0.03/
 25.006  MEME
 25.007  MEMC         V              3.0%          10inp-p
#!          Test Tol 0.01083, Sys Tol 0.0005166, TUR 20.964 (>= 4.00).
 26.001  IEEE         [@34401]FUNC "VOLT:AC"[GTL]
 26.002  IEEE         [@34401]SENS:DET:BAND 20
 26.003  DISP         Change the UUT frequency output to 20 Hz.
 26.003  DISP
 26.003  DISP         It may be necessary to adjust the CROSSOVER
 26.003  DISP         to keep channel 4 active.
 26.004  DISP         Set the UUT as follows:
 26.004  DISP         LEVEL MULTIPLIERS................... X100 (1in p-p)
 26.004  DISP         SERVO .............................. ON
 26.005  IEEE         [@34401]READ?[I][GTL]
 26.006  ACC    1     .1440V         0.06% 0.03/
 26.007  MEME
 26.008  MEMC         V              3.0%          1inp-p
#!          Test Tol 0.00432, Sys Tol 0.0003864, TUR 11.180 (>= 4.00).
 27.001  IEEE         [@34401]FUNC "VOLT:AC"[GTL]
 27.002  DISP         Change the UUT frequency output to 50 Hz.
 27.002  DISP
 27.002  DISP         It may be necessary to adjust the CROSSOVER
 27.002  DISP         to keep channel 4 active.
 27.003  DISP         Set the UUT as follows:
 27.003  DISP         LEVEL MULTIPLIERS................... X10 (.1in p-p)
 27.003  DISP         SERVO .............................. ON
 27.004  IEEE         [@34401]READ?[I][GTL]
 27.005  ACC    0.1   .0903V         0.06% 0.04/
 27.006  MEME
 27.007  MEMC         V              3.0%          1inp-p
#!          Test Tol 0.002709, Sys Tol 9.418e-005, TUR 28.764 (>= 4.00).
 28.001  IEEE         [@34401]FUNC "VOLT:AC"[GTL]
 28.002  DISP         Change the UUT frequency output to 500 Hz.
 28.002  DISP
 28.002  DISP         It may be necessary to adjust the CROSSOVER
 28.002  DISP         to keep channel 4 active.
 28.003  DISP         Set the UUT as follows:
 28.003  DISP         LEVEL MULTIPLIERS................... Both Out (.01in)
 28.003  DISP         SERVO .............................. ON
 28.004  IEEE         [@34401]READ?[I][GTL]
 28.005  ACC    1     .9030V         0.06% 0.03/
 28.006  MEME
 28.007  MEMC         V              3.0%          .01inp-p
#!          Test Tol 0.02709, Sys Tol 0.0008418, TUR 32.181 (>= 4.00).
 29.001  END
#! T.U.R.s less than 4.00:                  0
#! T.U.R.s estimated using RANGE value:     0
#! T.U.R.s not calculated (ASK- U):         0
#! T.U.R.s not computable at compile time:  0
#! FOR JUSTIFICATION REFER TO COMMENTS FOLLOWING EACH TEST IN THIS LISTING.